Too Many Bones Double-Sided Playmat: How to Use Both Sides

By Chip Theory Games | Published: 2026-10-31

Category: How-to Guides

Get the most from your Too Many Bones playmat: learn which side to use, how to set up the 34 x 48 surface, and simple care habits that keep it game-night ready.

Quick answer

Use the side printed for the mode you are playing, lay the mat flat on a clean, dry table, and arrange your Gearloc mat, loot, and dice around the Battle Mat. Wipe it down after each session and store it rolled or folded loosely to avoid permanent creases.

Why the 34 x 48 size changes your table setup

The Too Many Bones Double-Sided Playmat measures 34 x 48 inches, which is large enough to position each player’s Gearloc mat, loot, and dice around the central Battle Mat, Baddies, and Encounters. That layout matters because it keeps shared components within reach while giving each player a defined zone.

Before you unroll it, measure your table. The mat needs the full 34 x 48 footprint plus a little clearance for rulebooks, drink coasters, and anything you keep off the play surface. If your table is smaller, use the mat on the floor or a second folding table rather than letting components hang off the edge.

The side you are not using still needs care

A double-sided playmat doubles the surface you can damage. Grit, crumbs, or sticky residue on the table can transfer to the underside, and then to the printed side the next time you flip it. That is why the setup steps below start with cleaning the table, not the mat.

The mat is not described as waterproof or machine washable in the supplied product information, so treat it as a surface that should be wiped and aired rather than soaked. When in doubt, use a barely damp cloth and let it dry completely before rolling.

How to set up and care for both sides, step by step

Clear and clean the table: Remove crumbs, grit, and sticky rings from the entire table surface, then dry it fully. Common mistake: wiping only the middle of the table and leaving grit near the edges, which can transfer to the mat underside when you unroll it. Run a dry hand over the table after cleaning; if you feel any grit, wipe again before unrolling.
Choose the side for your game mode: Check the printed layout on each side and pick the one that matches the mode you are playing. If you are unsure which side is intended for your session, lay the mat printed-side up and compare the zones with your Gearloc mats and Battle Mat before placing any components. Do not flip the mat mid-game to test the other side; decide before components are placed.
Unroll and flatten the mat: Place the mat printed-side up on the clean table and smooth it from the center outward. If it was stored rolled, give it a few minutes to relax. Common mistake: forcing a curled edge flat with heavy components, which can crease the printed surface. If the mat still will not lie flat, roll it loosely in the opposite direction for a few minutes, then try again.
Build player zones around the Battle Mat: Position the Battle Mat, Baddies, and Encounters in the center, then place each player’s Gearloc mat, loot, and dice in the surrounding space. Leave a clear lane between player zones and the center so hands do not drag across cards. Check that every player can reach the Battle Mat without leaning across another player’s Gearloc mat.
Wipe down after play: After the session, remove components and wipe the printed surface with a barely damp, soft cloth, then let it air-dry completely. Common mistake: rolling or folding the mat while it is still damp, which can trap moisture against the printed side. If you used a damp cloth, wait until the surface feels dry to the touch before storing.
Store loosely to prevent creases: Roll the mat loosely or fold it with gentle curves, avoiding sharp creases along the printed areas. Keep it away from heat sources and direct sun. Common mistake: storing it under heavy boxes, which can press permanent folds into the surface. Store the mat on top of other game boxes, not underneath them.

Product facts

Too Many Bones Double-Sided Playmat: The Too Many Bones Double-Sided Playmat is a 34 x 48-inch surface designed to position Gearloc mats, loot, and dice around the Battle Mat, Baddies, and Encounters. That footprint gives every player a dedicated zone, so you can set up and tear down without sliding shared components across the table.
Too Many Bones Double-Sided Playmat